Plumbers in Grayslake IL understand that being able to tell the difference between a frozen pipe and a burst pipe is very important. Understanding that ta frozen pipe might be a burst pipe is important to understand as well. Knowing how to thaw out a frozen pipe is important to know how to fix a burst pipe. Being able to prevent pipes from becoming frozen is important but not very helpful after you already have broken or frozen pipes.
The first thing that you need to do is determine if you have a frozen pipe or a burst pipe. Plumbers in Grayslake IL know one of the only ways that you are able to determine if your pipe is frozen and not burst is if after it is thawed you have no water pressure. This will mean that you will need to know how to check and determine where a frozen pipe is located. The first indication that your pipes are frozen is there is no water coming out of your faucets and it was freezing temperatures the night before. You will want to look at your piping and see if you can find evidence that there is freezing along the pipe line. You will want to locate an area in the pipes that is colder than other areas of the pipe. You will want to start with pipes that are more likely to freeze such as those along the exterior wall, in the garage, in the basement, in the attic, and in crawl spaces with no insulation. Once you have located the frozen area in the pipes you have two options. The first would be to contact plumbers in Grayslake IL the second option is to take the time and thaw out the pipe and hope it is not burst.
Finding the Best Sump Pump in Crystal Lake IL
There are a number of ways that you heat the pipe to unfreeze it but please remember to be careful and safe when doing this. The first option that you have is to heat towels up and wrap them around the pipe and swapping them out when they become cold. This can take hours to get the pipe unfrozen. The next option is to get a blow dryer and heat the pipe up. You do not want to use fire because it could cause your house to burn down. You might be able to open the area up and allow the heat from your home to heat up the pipe. You will want to make sure that you remove everything that you can in the area that the pipe is frozen so you do not get water damage to them. When water is flowing freely you will need to check the water pressure. If you are not able to get the normal water pressure from your faucets you might be looking at a burst pipe which does not always happen at the spot of the frozen pipe. You will want to check and all the piping to see if there is water flowing from them. If you do find that you have a burst pipe you will want to shut off the water to that area and if that is not possible you will want to make sure that you turn off the main water valve. This will help you to help reduce the amount of water damage as well as save on your water bill.
Northern Cook County Plumbing Contractor
According to plumbers in Grayslake IL the first step that you need to do to be able to fix a burst pipe is to find the main water shut off valve. This is something that you should know even if you are not working with it because when you are seeing gushing water where there should not be gushing water that is your best chance to get it to stop. The next step in repairing a burst pipe would be to make sure that you turn off the water supply. You will then want to turn on a faucet so that you are able to get out any water that might be in the pipes. You will then need to place a bucket under the area of pipe that you are cutting in case any water might be remaining in the line. The next step would be to cut out the section of the pipe that needs to be removed. You will want to rotate the pipe cutter around the pipe, slightly tightening the pipe cutter until it cut through the pipe. You will then need to take off any burrs that are left of the end of the pipe with steel wool. You will then need to temporarily remove the small screw from the valve. Make sure that you are noting the direction that you are installing it at. There should be an arrow that dictates the way that water flows to assist in making sure that you are properly installing it right. The next step that you will need to take would be to cut a section of copper pipe to the right length. Plumbers in Grayslake IL suggest that you allow a little extra length to be able to get a good fit. You will need to make sure that the new pipe is the same diameter as the old pipe. You will want to use steel wool to clean the stop-and-waste valve as well as the pipe. Plumbers in Grayslake IL suggest that you spread soldering flux on the inside of the valve fitting as well as on the outside of the pipe.
Find Your Plumbing Repair in Crystal Lake IL
You will need to slide the valve fitting onto the end of the pipe. Plumbers in Grayslake IL suggest that you wear safety goggles when you use a propane torch which you will need to do to heat the fitting and the pipe where they connect. You should hold the blue flame right against the pipe to get the best results. You will want need to push about 2-inches into the joint where the valve connects to the pipe. The heat should melt the solder and allow it to seep into the connection. Plumbers in Grayslake IL suggest that you practice this on scrap pipe and copper fittings before you do it on the valve to ensure that you do not make a mistake. You will then want to replace the petcock and open the main water line to check for any leaks. You will want to get heating tape of foam insulation for tapes to ensure that you do not have a repeat of this problem. For those that might find that they do not feel comfortable with completing these steps or might not have all the tools that they need to be able to complete this task will want to call a professional in to get the job done quickly.
For more information on Grayslake IL plumbers for burst pipe assistance or for other plumbing emergency help feel free to give us a call at .